High Efficiency Factory PTFE Graphite Braided Packing for Kyrgyzstan Factory
High Efficiency Factory PTFE Graphite Braided Packing for Kyrgyzstan Factory Detail:
It is a braided packing made of PTFE yarn containing graphite. It is recommended for shafts for almost all chemicals. Stability and long service lift are achieved by low friction coefficient. It has great tear strength and high thermal conductivity. This self lubrication packing does not score the shaft and minimizes sleeve rep, acement cost. It can be used to seal alkalis, solvents, water, steam, acids except strong oxidizing acids( aqua regia, fuming nitric acid, fuming nitric acid, fuming sulfuric acid,etc.) for centrifugal pumps, autoclaes, agitators mixers, etc.
Technical Data Sheet
|
Rotating |
Reciprocating |
Valves |
Pressure |
2Mpa |
15Mpa |
15Mpa |
Shaft Speed |
14m/s rotary |
||
Temperature |
-200℃~+280℃ |
||
PH Range |
0~14 |
Application Area
It can be used to seal alkalis, solvents, water, steam, for centrifugal pumps, autoclaves, agitators, mixers, etc.
Product detail pictures:
Related Product Guide:
A Look at the Molded Gasket
O-Ring Sizes for Industrial Applications
High Efficiency Factory PTFE Graphite Braided Packing for Kyrgyzstan Factory, The product will supply to all over the world, such as: , , ,
In this video I cover repairing both internal and external oil leaks on 1994-1997 Honda 4 cylinder engine distributors.
Many state if the distributor is leaking internally it can’t be repaired and to buy a new distributor. Well with the right part number and a bit of patience. You can fix that internal oil leak and save yourself at least 180 bucks.
I also address repairing the common outer seal leak as well.
Here are the part numbers you’ll need. There are different part numbers depending on which distributor you have.
You either have a Tec distributor with an external ignition coil or a Hitachi distributor with an internal ignition coil. The Tec distributor caps have 5 wires on them while the Hitachi’s have 4 wires on their cap.
The Hitachi distributors require a bit more internal disassembly but the seal replacement process is identical to the Tec shown in the video.
Tec Part Numbers:
Outer O-Ring Seal: 30110-PA1-732 (From Honda).
Inner Shaft Seal Part Number: NOK BH3888E (Order Online). The dimensions of this seal are 12.5 X 22.5 X 5mm.
Hitachi part numbers:
Outer O-Ring Seal: 30110-PC6-005 (From Honda).
Inner Shaft Seal Part Number: KOK 3286 (Order Online). The dimensions of this seal are 12.45mm X 22mm X 6mm.
If you replace your heater core inlet hose you’ll need to bleed the cooling system.
Here is a link to my video on bleeding the cooling system:
https://www.youtube.com/watch?v=owQcxSrKARA
Intro and outro music Hot Swing by Kevin Macleod (Incompetech.com).
Due to factors beyond the control of Bushougoma, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bushougoma assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bushougoma recommends safe practices when working with the tools or equipment seen or implied in this video. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Bushougoma.
Burlington based ISPAT Machining creating and repairing custom industrial pumps, parts, and mechanical seals and industrial machining. https://www.ispatmachining.com
By from -
By from -