China wholesale FEP Encapsulated O-Ring to Mexico Factory
China wholesale FEP Encapsulated O-Ring to Mexico Factory Detail:
Encapsulated O Ring adopts special rubber resisting high temperature, F+ plastic and special engineering to compound this sealing product. It not only has low contraction permanent set functions of rubber O Ring, but also resistant heat, cold oil, friction, chemical corrusion and other performances. It can be used in all kind of dynamical seal and static seal widely, meanwhile can replace all traditional rubber and plastic O Ring.
Technical Data Sheet
|
Property |
Unit |
Result |
|||
|
A |
B |
C |
|||
|
Normal Conditions |
Hardness |
JIS Hs |
70~90 |
70~90 |
60~75 |
|
Elongations(min.) |
% |
60 |
60 |
80 |
|
|
Tensile Stress(min) |
Mpa |
16 |
16 |
16 |
|
|
Compressibility |
% |
50~60 |
50~60 |
60~75 |
|
|
Recovery |
% |
＞85 |
＞85 |
＞70 |
|
|
Permanentset |
% |
＜10 |
＜10 |
＜10 |
|
|
230°Cx24h hot air ageing |
Change of hardness(max) |
JIS Hs |
-5~+5 |
-5~+5 |
-5~+5 |
|
Change of Tensile Stress(max) |
% |
-15 |
-15 |
-15 |
|
|
Change of Elongation(max) |
% |
-20 |
-20 |
-20 |
|
|
Compression Permanentset |
175°Cx70h |
% |
≤20 |
≤20 |
≤20 |
|
Color |
|
|
Brown |
Black |
Red |
|
Applications |
Temperature Limited |
℃ |
-20~+250 |
-20~+200 |
-20~+200 |
|
Pressure Limited |
Mpa |
0~35 |
|||
|
Working Environment |
|
Strong Caustics, moderate acids, chlorine, gases, water, steam, hydrocarbons, hydrogen and aluminum fluoride except element fluorine and fusion sodium. |
|||
Product detail pictures:
Related Product Guide:
Comparison of O-Ring Materials
A Look at the Molded Gasket
China wholesale FEP Encapsulated O-Ring to Mexico Factory, The product will supply to all over the world, such as: , , ,
https://www.ReplicaAirguns.com – How to Fix Leaking CO2 in an Airgun.
A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.
There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.
When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.
Watch my YouTube video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.
Checkout my other articles, reviews and posts over at:
https://www.ReplicaAirguns.com
Buy Replica Guns in Canada:
https://www.replicaairguns.ca/
Buy Replica Guns in the US:
https://www.replicaairguns.com/buy-air-blank-guns-us/
By from -
By from -
