OEM/ODM China Flexible Graphite Braided Packing Export to Korea

The Flexible Graphite braided packing is made of an innovative expanded pure graphite yarn. The combination of other braided packing which is made of an innovative expanded pure graphite yarn. The combination of other braided packing installed with the excellent sealing capabilities of expanded pure graphite makes it the most effective sealing component.

Technical Data Sheet

 Application Area

It can be used to seal hot water, high temperature and pressure steam, heat transfer fluid, hydrogen gas, ammonia, organic solvents, hydrocarbons, cryogenic liquids, etc., except fewer strong oxidizer. It is a unique and universal sealing packing.

I DO COMPLETE VALVE STEM SEALS FOR $3000. DEALER PRICE $8-12K
EMAIL ME @: knightsmastertech@gmail.com (Leave your contact info)

After noticing white smoke w/a bluish tint coming from the tale pipe of my 745I , I began to read blogs on consumers experiencing very similar issues. After reading over a dozen blogs that described the exact same issues I experienced, it became clear that the issue was the VALVE STEM SEALS. They needed to be replaced. My check engine light was on and read code p0492 (secondary air Fault bank 2). I had the emission control valve replaced a few months ago & in less than a week, the check engine light was back on. At this point, I felt I knew more than what the auto repair guys did & besides, my pockets couldn’t handle seeing much more of them, so I decided to do the work myself, of course, this wouldn’t be my first time. I purchased both the AGA Valve Stem Seal tool and AGA Secondary Air Cleaner Kit to complete these tasks. I will do my best to explain in detail all necessary steps needed in order to eliminate the above listed code and clear up the white smoke blowing out of the exhaust pipe. TO COMPLETE WHAT I’M ABOUT TO SHOW YOU WILL COST TWO ARMS, YOUR FIRST AND LAST BORN AND YOU’RE LEGS.

DEALER COST:
-VALVE STEM SEALS $8-12K (check it out for yourself)
-SECONDARY AIR SYSTEM CLEANING $6K
-NOT TO MENTION EVERYTHING ELSE BELOW.

I can & will replace the Valve Cover Gasket, Timing Cover Gasket, Engine/Cabin Air Filters and a host of O-Rings that is listed in detail…

For this E65/E66/N62 DIY job
-Valve Stem Oil Seals: 11340029751 – Qty: 2 (16 in a pack)
-Valve Cover Gaskets (Cyl. 1-4):
-Valve Cover Gaskets (Cyl. 5-8):
-Engine Timing Chain Case Gasket: 11147506424 – Qty: 1
-Engine Timing Chain Case Gasket: 11147506425 – Qty: 1
-Vanos Solenoid O-Ring: 11367513222 – Qty: 4
-Brake Vacuum Pump O-Ring:
-Eccentric Shaft Actuator Seal: 07119903596 – Qty: 2
-Eccentric Shaft Sensor Seal: 11127518420 – Qty: 2
-Valve Cover Grommet: 11127511582 – Qty: 4 (optional)
-Cam Sensor O-Ring: 12141748398 – Qty: 4
-Engine Air Filter: C301531 – Qty: 1
-Cabin Air Filter (Activated Charcoal): CUK31242 – Qty: 1
-Spark Plug Tube: 112757021

Difficulty level 1-10: 9 — because of so much that have to be removed and the sensitive sensors that could be broken while removing and installing. It took me five days due to getting used to the tools that I had to use.

While everything is a loose its time to replace the Valve Stem Seals using the N62 Valve Stem Seal Tool. I’m not going to go into detail about how to use the tool because AGA does a step-by-step video of the entire procedure. Note: When doing the valve stem seals make sure that intermediate lever is in place with the spring behind the V.

I would say after a few times of using the listed tools, the job became a lot smoother.

As for the code p0492 (secondary air injection) while everything is a part, it is easier to slide your hand behind the engine (so you don’t need a pair of little girl hands) to remove the air tube for the cleaning that specified in AGA video. It just makes the job go a little easier. I’m not going into detail about how to use the tool because AGA does a step-by-step video of the entire procedure

CAR NOT SMOKING ANYMORE AND RUNS LIKE NEW. TOOK A JOB THAT WOULD HAVE COST ANYWHERE BETWEEN 14-20K AT THE DEALER and turned it into a much affordable job IN JUST 4 DAYS.

MESSAGE ME WITH ANY QUESTIONS

Shanghai Kuko Packing Machinery Co., Ltd
Address: No. 4568, JiHe Road, Qingpu District, Shanghai, 201709, China
Tel: 86-(0)21-69746020 52265219
Contact : Cecilia Pii
Emai:Cecilia@goodpacking.com.cn
Mobile: +86 189 1774 9969

 Application: Suits for doors, curtain frames, floors, ladders, windows, etc;(Special design for floor)
 Sealing speed is up to 8meters per minute for fast and efficient production;
 Easy to use, programmable computer controlled memory that reduces down time due to product changes.
 Adjustable according to different sizes with simple operation.
 Seal-cut is completed continuously without operator, high level of automatic, wide use.
 The blade with Teflon treatment can endure high temperature without sticking;
 Sealing and cutting system with constant temperature makes the sealing straight, firm and beautiful;
 Banner photocell detects the product delivery accurately;
 The machine applies the most advanced Siemens PLC accompanied with touch screen guarantee the precise action;
 Waste film recycling system creates a clean and safe production atmosphere;
 Hot air circulating shrink tunnel uses stainless steel heating elements which could ensure long life span; the shrinking temperature and conveyor speed are adjustable;
 Conveyor unit of shrink tunnel has Teflon mesh type or rod-shaped chain type for your option;
 All the switches are Siemens;
 The machine suits for packing long products with unlimited length; high level of automation could be widely used in mass production;
 The finished products are neat, compact and suitable for storage and prolonged transport.

Model GH-3015L
Power 380V 50Hz 3phase
220V 60Hz 3phase
Length of cutter 500mm
Max. packing size L (No limited) x W300 x H150mm
Packing speed 35packs/min
Machine dimension L2090xW1560xH1320mm
Air source 5.5Kg/cm3

Sealing Part 　 　
Item Name Brand Remarks
Photocell Banner From U.S.A
Solid Relay Kudom From U.K
Cylinder Festo From Germany
Solenoid Valve Festo From Germany
Reducing Motor GPG From Taiwan
Film Motor Bolong From Shanghai
PLC Siemens From Germany
Touch Screen Siemens From Germany
All Switches Siemens From Germany
Heating Elements Home-made From China
Cutter Home-made From China

Shrink Tunnel 　 　
Item Name Brand Remarks
Solid Relay Kudom From U.K
Reducing Motor GPG From Taiwan
Recycling Motor Bolong From Shanghai
Temperature Controller Omron From Japan
Frequency Inverter Schneider From France
All Switches Siemens From Germany
Insulation Aluminum Silicate 5cm thickness
Intermediate Relay Siemens From Germany