Factory Wholesale PriceList for FEP Encapsulated O-Ring Export to Holland
Factory Wholesale PriceList for FEP Encapsulated O-Ring Export to Holland Detail:
Encapsulated O Ring adopts special rubber resisting high temperature, F+ plastic and special engineering to compound this sealing product. It not only has low contraction permanent set functions of rubber O Ring, but also resistant heat, cold oil, friction, chemical corrusion and other performances. It can be used in all kind of dynamical seal and static seal widely, meanwhile can replace all traditional rubber and plastic O Ring.
Technical Data Sheet
|
Property |
Unit |
Result |
|||
|
A |
B |
C |
|||
|
Normal Conditions |
Hardness |
JIS Hs |
70~90 |
70~90 |
60~75 |
|
Elongations(min.) |
% |
60 |
60 |
80 |
|
|
Tensile Stress(min) |
Mpa |
16 |
16 |
16 |
|
|
Compressibility |
% |
50~60 |
50~60 |
60~75 |
|
|
Recovery |
% |
＞85 |
＞85 |
＞70 |
|
|
Permanentset |
% |
＜10 |
＜10 |
＜10 |
|
|
230°Cx24h hot air ageing |
Change of hardness(max) |
JIS Hs |
-5~+5 |
-5~+5 |
-5~+5 |
|
Change of Tensile Stress(max) |
% |
-15 |
-15 |
-15 |
|
|
Change of Elongation(max) |
% |
-20 |
-20 |
-20 |
|
|
Compression Permanentset |
175°Cx70h |
% |
≤20 |
≤20 |
≤20 |
|
Color |
|
|
Brown |
Black |
Red |
|
Applications |
Temperature Limited |
℃ |
-20~+250 |
-20~+200 |
-20~+200 |
|
Pressure Limited |
Mpa |
0~35 |
|||
|
Working Environment |
|
Strong Caustics, moderate acids, chlorine, gases, water, steam, hydrocarbons, hydrogen and aluminum fluoride except element fluorine and fusion sodium. |
|||
Product detail pictures:
Related Product Guide:
A Look at the Molded Gasket
What Is A PTFE Ring Gasket?
Factory Wholesale PriceList for FEP Encapsulated O-Ring Export to Holland, The product will supply to all over the world, such as: , , ,
Visit https://parts.rheem.com to buy manufacturer authorized parts for Rheem, Ruud, Richmond, Marathon, Eclipse, Vanguard, Hotpoint and General Electric (GE) water heaters. We also offer many universal parts designed to fit most other brands of water heaters.
The temperature and pressure relief valve (T&P) is an important safety feature that prevents pressure from building up that could damage the water heater and even your home. Over time, corrosion can cause the T&P valve to no longer function as it should. To determine if your T&P valve is working properly, open the valve with your hand by pulling up the lever as shown in the video. When pulling up on this lever, you should hear pressure escape the valve. If it doesn’t pass that simple test, it’s time to replace the valve.
This video shows detailed step-by-step procedure for how to replace a T&P valve on a gas or electric hot water heater.
Tools you’ll need
Replacement T&P Valve
Pipe wrench or adjustable wrench
Extension or Cheater bar
Pipe sealer or Teflon Tape
Garden hose
Rags or Towels
WARNING: For your safety, be sure to carefully read and understand the manufacturer’s Use and Care Manual, in its entirety, prior to operating, repairing or adjusting the water heater. Failure to do so may result in fire or explosion, electric shock, property damage, personal injury, or loss of life. If you do not understand these instruction or any terms within them, please contact a qualified service professional. Prior to starting any repairs or service on your water heater, please thoroughly read the Use and Care Manual provided with your water heater. If at any time you are unsure or uncomfortable about the suggested repair or service discussed herein, stop any activity and immediately contact a licensed plumber.
Modular back-ups, MB profile, are specifically designed to compliment the PolyPak profiles. To help make the selection and ordering of the correct part number for the MB profile easy and efficient, the part numbering system used is very similar to that of the PolyPak. By formulating high modulus blends of Molythane (4617) and PolyMyte (4652), Parker has ensured that MB back-ups can be used with either type of base sealing material while maintaining the expected temperature range and fluid compatibility. The robust design ensures pressure ratings up to 10,000 psi are met.
Back-up rings are the most common anti-extrusion devices in dynamic sealing. They provide simple solutions to safely increase system pressure or solve an existing seal extrusion problem. Back-up rings function by positioning a more robust material adjacent to the extrusion gap, taking the seal’s place and providing a barrier against high pressures. Back-ups can be used to offset the reduced pressure rating effects of wear rings or to improve seal life at increased pressures. They can also be used to protect seals against pressure spikes, or to ensure seal performance at higher temperatures.
By from -
By from -
