Factory directly provided Expanded PTFE Tape for Mauritania Importers
Factory directly provided Expanded PTFE Tape for Mauritania Importers Detail:
Expanded PTFE sealant tape possesses all the properties of PTFE, resistant to all the corrosive media.
Soft, twistable and bendable at will. Even if gravely rusted and worn out sealing face, as long as it is used, the equipment units may continue their service and the sealing can keep its best performance.
Excellent anti-wriggle variation ability and cold current resistance. Even in case of cross change of temperature and pressure, good sealing can be assured.
l Easy use and replacement
l Wide service scope.
Technical Data Sheet
|
No.
|
Project |
Technical Indexes |
|
1 |
PH Range |
0-14 |
|
2 |
Density |
0.7-0.8g/cm3 |
|
3 |
Temperature resistance |
-260-+260℃ |
|
4 |
High pressure resistance |
20~25Mpa |
|
5 |
Elongation |
20~30% |
|
6 |
Tensile strength |
30~35Mpa |
Regular Size
|
NO. |
SIZE |
NO. |
SIZE |
|
1 |
3mm*1.5mm*30m |
15 |
16mm*4mm*10m |
|
2 |
3mm*2mm*30m |
16 |
20mm*3mm*5m |
|
3 |
6mm*3mm*20m |
17 |
20mm*4mm*5m |
|
4 |
7mm*2.5mm*20m |
18 |
20mm*5mm*5m |
|
5 |
9mm*3mm*15m |
19 |
20mm*7mm*5m |
|
6 |
9mm*4mm*15m |
20 |
25mm*4mm*5m |
|
7 |
10mm*3mm*10m |
21 |
25mm*5mm*5m |
|
8 |
10mm*4mm*10m |
22 |
25mm*8mm*5m |
|
9 |
10mm*5mm*10m |
23 |
25mm*10mm*5m |
|
10 |
12mm*3mm*10m |
24 |
30mm*3mm*5m |
|
11 |
12mm*4mm*10m |
25 |
30mm*4mm*5m |
|
12 |
12mm*5mm*10m |
26 |
40mm*4mm*5m |
|
13 |
12mm*6mm*10m |
27 |
50mm*4mm*5m |
|
14 |
14mm*5mm*10m |
28 |
100mm*0.5mm*10m |
Application Area
It can be widely used in diverse pipelines to seal flanges, enameled products, glass, rubber products, plastics, non-rusting graphite lining tower, heat exchanger, pressure container as linings and to seal their flanges, to seal the fillers of diverse pumps and valves and to seal much heavy-calibre flanges which are not so precise, have larger unflat area and irregular shapes and require not too large tighting force.
Product detail pictures:
Related Product Guide:
What Is A PTFE Ring Gasket?
A Look at the Molded Gasket
Factory directly provided Expanded PTFE Tape for Mauritania Importers, The product will supply to all over the world, such as: , , ,
https://www.ReplicaAirguns.com – How to Fix Leaking CO2 in an Airgun.
A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.
There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.
When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.
Watch my YouTube video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.
Checkout my other articles, reviews and posts over at:
https://www.ReplicaAirguns.com
Buy Replica Guns in Canada:
https://www.replicaairguns.ca/
Buy Replica Guns in the US:
https://www.replicaairguns.com/buy-air-blank-guns-us/
By from -
By from -
