Factory Free sample Expanded PTFE Tape to New York Manufacturers
Factory Free sample Expanded PTFE Tape to New York Manufacturers Detail:
Expanded PTFE sealant tape possesses all the properties of PTFE, resistant to all the corrosive media.
Soft, twistable and bendable at will. Even if gravely rusted and worn out sealing face, as long as it is used, the equipment units may continue their service and the sealing can keep its best performance.
Excellent anti-wriggle variation ability and cold current resistance. Even in case of cross change of temperature and pressure, good sealing can be assured.
l Easy use and replacement
l Wide service scope.
Technical Data Sheet
No.
|
Project |
Technical Indexes |
1 |
PH Range |
0-14 |
2 |
Density |
0.7-0.8g/cm3 |
3 |
Temperature resistance |
-260-+260℃ |
4 |
High pressure resistance |
20~25Mpa |
5 |
Elongation |
20~30% |
6 |
Tensile strength |
30~35Mpa |
Regular Size
NO. |
SIZE |
NO. |
SIZE |
1 |
3mm*1.5mm*30m |
15 |
16mm*4mm*10m |
2 |
3mm*2mm*30m |
16 |
20mm*3mm*5m |
3 |
6mm*3mm*20m |
17 |
20mm*4mm*5m |
4 |
7mm*2.5mm*20m |
18 |
20mm*5mm*5m |
5 |
9mm*3mm*15m |
19 |
20mm*7mm*5m |
6 |
9mm*4mm*15m |
20 |
25mm*4mm*5m |
7 |
10mm*3mm*10m |
21 |
25mm*5mm*5m |
8 |
10mm*4mm*10m |
22 |
25mm*8mm*5m |
9 |
10mm*5mm*10m |
23 |
25mm*10mm*5m |
10 |
12mm*3mm*10m |
24 |
30mm*3mm*5m |
11 |
12mm*4mm*10m |
25 |
30mm*4mm*5m |
12 |
12mm*5mm*10m |
26 |
40mm*4mm*5m |
13 |
12mm*6mm*10m |
27 |
50mm*4mm*5m |
14 |
14mm*5mm*10m |
28 |
100mm*0.5mm*10m |
Application Area
It can be widely used in diverse pipelines to seal flanges, enameled products, glass, rubber products, plastics, non-rusting graphite lining tower, heat exchanger, pressure container as linings and to seal their flanges, to seal the fillers of diverse pumps and valves and to seal much heavy-calibre flanges which are not so precise, have larger unflat area and irregular shapes and require not too large tighting force.
Product detail pictures:
Related Product Guide:
What Is A PTFE Ring Gasket?
O-Ring Sizes for Industrial Applications
Factory Free sample Expanded PTFE Tape to New York Manufacturers, The product will supply to all over the world, such as: , , ,
How to replace the oil seal for the saginaw steering gearbox Pitman-arm shaft. Here we dis-assemble the gearbox to investigate what cause the oil seal to fail. We found the tension spring behind the rubber lip seal to be corroded and nearly broken. We were able to locate a new non-brand name oil seal with a different sealing lip profile, but the new seal became damage while installing into the saginaw casting. We reuse the old seal by replacing its tension spring from the new oil seal. We also lost a few video clips from this recording but we feel the video achieve its purpose of how to replace the oil seal for the saginaw steering gearbox. You should also see the first part of this series by
CLICK HERE . https://www.youtube.com/watch?v=EaK_pc95Poo
Part 2. https://www.youtube.com/watch?v=wlN-KDn-YCQ
Part 3.https://www.youtube.com/watch?v=oX7zVcDEJqM
CLICK HERE for Seal PART number
The model 800(Nissan D600) incorporates a recirculating ball system in which steel balls act as a rolling thead between a steering worm-shaft and the rack-piston. Whenever a part which forms a sealing surface for an “o” ring is removed , the “o” ring seal should also be removed and replaced with a new seal. Whenever one of the pitman shaft or stub shaft seals are removed all adjacent seals should be removed and replaced with new seals. Lubricate all new seals with power steering fluid to ease assembly.
CAUTION. USE THE PROPER TOOL TO SEPARATE ALL TIE ROD AND BALL JOINTS.
Torque small 14mm hydralic line to 22-29lbs ft.
Torque large 16mm hydralic line fitting to 29-36 lbs-ft.
Thank you.
Also see.
https://www.youtube.com/watch?v=hdfWXfsEZz8 . part series on restoring vehicle front-end alignment and road safe.
https://www.youtube.com/watch?v=3adLcniKrwA self packing a 4×4 front wheel hub bearing for lifetime operation.
Troubleshooting why the vehicle DO NOT START.https://www.youtube.com/watch?v=YCZMhOta_pE
please visit the channel Homepage for more in detail automotive repair and fix it video. Thank you.
Special tools thanks to Stanely Bostitch company. Tool # 84-273 is 7″ or 178mm Circlip Pliers(Alicate para Anillo de Retencion)
By from -
By from -