15 Years Factory wholesale PTFE Graphite Braided Packing Export to Qatar

Short Description:

It is a braided packing made of PTFE yarn containing graphite. It is recommended for shafts for almost all chemicals. Stability and long service lift are achieved by low friction coefficient. It has great tear strength and high thermal conductivity. This self lubrication packing does not score the shaft and minimizes sleeve rep, acement cost. It can be used to seal alkalis, solvents, water, steam, acids except strong oxidizing acids( aqua regia, fuming nitric acid, fuming nitric acid, fuming ...


Product Detail

Product Tags

Related Video

Feedback (2)

, , ,
15 Years Factory wholesale PTFE Graphite Braided Packing Export to Qatar Detail:

It is a braided packing made of PTFE yarn containing graphite. It is recommended for shafts for almost all chemicals. Stability and long service lift are achieved by low friction coefficient. It has great tear strength and high thermal conductivity. This self lubrication packing does not score the shaft and minimizes sleeve rep, acement cost. It can be used to seal alkalis, solvents, water, steam, acids except strong oxidizing acids( aqua regia, fuming nitric acid, fuming nitric acid, fuming sulfuric acid,etc.) for centrifugal pumps, autoclaes, agitators mixers, etc.

Technical Data Sheet

 

Rotating

Reciprocating

Valves

Pressure

2Mpa

15Mpa

15Mpa

Shaft Speed

14m/s rotary

Temperature

-200℃~+280℃

PH Range

0~14

 Application Area

It can be used to seal alkalis, solvents, water, steam, for centrifugal pumps, autoclaves, agitators, mixers, etc.


Product detail pictures:

15 Years Factory wholesale
 PTFE Graphite Braided Packing Export to Qatar detail pictures


Related Product Guide:
Comparison of O-Ring Materials
A Look at the Molded Gasket

15 Years Factory wholesale PTFE Graphite Braided Packing Export to Qatar, The product will supply to all over the world, such as: , , ,


  • Visit https://parts.rheem.com to buy manufacturer authorized parts for Rheem, Ruud, Richmond, Marathon, Eclipse, Vanguard, Hotpoint and General Electric (GE) water heaters. We also offer many universal parts designed to fit most other brands of water heaters.

    Changing the anode rod every four years is a great way to extend the life of your water heater. The anode rod is a special metal component that’s meant to slowly dissolve so that the tank itself doesn’t corrode. When the anode rod is depleted, it no longer offers corrosion protection for the tank. To avoid tank damage, it’s best to replace the rod before that happens.

    We offer anodes made from magnesium and aluminum, available in various lengths. Aluminum rods are available where sulfur odor or “rotten eggs smell” is a problem. Flexible rods are available where overhead space is tight for installation.

    This video shows detailed step-by-step procedure for how to replace an anode rod on a gas or electric hot water heater.

    Tools you’ll need
    A ratchet wrench
    A 1 1/16-inch socket
    A 24” cheater bar or pipe
    A Flat Blade Screwdriver
    Teflon tape
    A 2-gallon bucket
    Hack saw

    WARNING: For your safety, be sure to carefully read and understand the manufacturer’s Use and Care Manual, in its entirety, prior to operating, repairing or adjusting the water heater. Failure to do so may result in fire or explosion, electric shock, property damage, personal injury, or loss of life. If you do not understand these instruction or any terms within them, please contact a qualified service professional. Prior to starting any repairs or service on your water heater, please thoroughly read the Use and Care Manual provided with your water heater. If at any time you are unsure or uncomfortable about the suggested repair or service discussed herein, stop any activity and immediately contact a licensed plumber.


    5 Stars By from -

    5 Stars By from -

    Related Products