18 Years Factory offer Spiral Wound Gasket-CGI Export to Slovakia

Short Description:

Spiral wound gasket consists of “V-shape”(or”W-shape”)metal tape and nonmetal tape, which are overlapped each other and wound continuously.To fasten the metal tape,both its start point and end point are tack welded. Feature Wide Scope of acceptable working conditions. Can be used under high temperature, high pressure and ultra-low temperature or vacuum conditions. Change the combination of the gasket materials is to tackle the chemical corrosion problem of diverse medi...


Product Detail

Product Tags

Related Video

Feedback (2)

We attempt for excellence, provider the customers", hopes to be the most beneficial cooperation team and dominator enterprise for staff, suppliers and shoppers, realizes value share and continuous advertising for Ptfe Flat Gasket , Fep Encapsulated Viton O Ring , Ptfe Epdm Gasket , Good quality and competitive prices make our products enjoy a high reputation all over the word.
18 Years Factory offer Spiral Wound Gasket-CGI Export to Slovakia Detail:

Spiral wound gasket consists of “V-shape”(or”W-shape”)metal tape and nonmetal tape, which are overlapped each other and wound continuously.To fasten the metal tape,both its start point and end point are tack welded.

Feature

Wide Scope of acceptable working conditions. Can be used under high temperature, high pressure and ultra-low temperature or vacuum conditions. Change the combination of the gasket materials is to tackle the chemical corrosion problem of diverse media toward the gasket.

Not very rigid requirements to the surface precision of the flange. May be used to seal flanges with rough surface

Easy installation and handy use.

Excellent Sealability

Products Type

dd

Technical Data Sheet

Product&Type

Size(mm)

Temperature(℃)

Pressure(Mpa)

Spiral Wound Gasket filled with Graphite

 

φ16~φ3200

(In Oxidizing Environment )-240~+550℃;(In non-Oxidizing Environment)-240~+870℃

(Under hot water, oil etc. )30 Mpa; (Under vapor oil, gases etc.)20 Mpa

Spiral Wound Gasket filled with Asbestos

 

φ16~φ3200

-150~+450℃

15

Spiral Wound Gasket filled with PTFE

 

φ16~φ3200

-200~+250℃

15

Application Area

The Spiral Wound Gaskets are mainly used in valves &pipes, pressure vessel, condenser, heat exchanger flanges in oil, chemical, metallurgy, vessel and mechanical industries.


Product detail pictures:

18 Years Factory offer
 Spiral Wound Gasket-CGI Export to Slovakia detail pictures


Related Product Guide:
Comparison of O-Ring Materials
O-Ring Sizes for Industrial Applications

We emphasize progress and introduce new solutions into the market each year for 18 Years Factory offer Spiral Wound Gasket-CGI Export to Slovakia, The product will supply to all over the world, such as: Grenada , Hungary , South Africa , Now, with the development of internet, and the trend of internationalization, we have decided to extend business to overseas market. With the propose of bringing more profits to oversea customers by providing directly abroad. So we have changed our mind, from home to abroad, hope to give our customers more profit, and looking forward to more chance to make business.


  • I DO COMPLETE VALVE STEM SEALS FOR $3000. DEALER PRICE $8-12K
    EMAIL ME @: knightsmastertech@gmail.com (Leave your contact info)

    After noticing white smoke w/a bluish tint coming from the tale pipe of my 745I , I began to read blogs on consumers experiencing very similar issues. After reading over a dozen blogs that described the exact same issues I experienced, it became clear that the issue was the VALVE STEM SEALS. They needed to be replaced. My check engine light was on and read code p0492 (secondary air Fault bank 2). I had the emission control valve replaced a few months ago & in less than a week, the check engine light was back on. At this point, I felt I knew more than what the auto repair guys did & besides, my pockets couldn’t handle seeing much more of them, so I decided to do the work myself, of course, this wouldn’t be my first time. I purchased both the AGA Valve Stem Seal tool and AGA Secondary Air Cleaner Kit to complete these tasks. I will do my best to explain in detail all necessary steps needed in order to eliminate the above listed code and clear up the white smoke blowing out of the exhaust pipe. TO COMPLETE WHAT I’M ABOUT TO SHOW YOU WILL COST TWO ARMS, YOUR FIRST AND LAST BORN AND YOU’RE LEGS.

    DEALER COST:
    -VALVE STEM SEALS $8-12K (check it out for yourself)
    -SECONDARY AIR SYSTEM CLEANING $6K
    -NOT TO MENTION EVERYTHING ELSE BELOW.

    I can & will replace the Valve Cover Gasket, Timing Cover Gasket, Engine/Cabin Air Filters and a host of O-Rings that is listed in detail…

    For this E65/E66/N62 DIY job
    -Valve Stem Oil Seals: 11340029751 – Qty: 2 (16 in a pack)
    -Valve Cover Gaskets (Cyl. 1-4):
    -Valve Cover Gaskets (Cyl. 5-8):
    -Engine Timing Chain Case Gasket: 11147506424 – Qty: 1
    -Engine Timing Chain Case Gasket: 11147506425 – Qty: 1
    -Vanos Solenoid O-Ring: 11367513222 – Qty: 4
    -Brake Vacuum Pump O-Ring:
    -Eccentric Shaft Actuator Seal: 07119903596 – Qty: 2
    -Eccentric Shaft Sensor Seal: 11127518420 – Qty: 2
    -Valve Cover Grommet: 11127511582 – Qty: 4 (optional)
    -Cam Sensor O-Ring: 12141748398 – Qty: 4
    -Engine Air Filter: C301531 – Qty: 1
    -Cabin Air Filter (Activated Charcoal): CUK31242 – Qty: 1
    -Spark Plug Tube: 112757021

    Difficulty level 1-10: 9 — because of so much that have to be removed and the sensitive sensors that could be broken while removing and installing. It took me five days due to getting used to the tools that I had to use.

    While everything is a loose its time to replace the Valve Stem Seals using the N62 Valve Stem Seal Tool. I’m not going to go into detail about how to use the tool because AGA does a step-by-step video of the entire procedure. Note: When doing the valve stem seals make sure that intermediate lever is in place with the spring behind the V.

    I would say after a few times of using the listed tools, the job became a lot smoother.

    As for the code p0492 (secondary air injection) while everything is a part, it is easier to slide your hand behind the engine (so you don’t need a pair of little girl hands) to remove the air tube for the cleaning that specified in AGA video. It just makes the job go a little easier. I’m not going into detail about how to use the tool because AGA does a step-by-step video of the entire procedure

    CAR NOT SMOKING ANYMORE AND RUNS LIKE NEW. TOOK A JOB THAT WOULD HAVE COST ANYWHERE BETWEEN 14-20K AT THE DEALER and turned it into a much affordable job IN JUST 4 DAYS.

    MESSAGE ME WITH ANY QUESTIONS

    The company's products very well, we have purchased and cooperated many times, fair price and assured quality, in short, this is a trustworthy company!
    5 Stars By Penelope from Libya - 2016.10.25 15:53
    The after-sale warranty service is timely and thoughtful, encounter problems can be resolved very quickly, we feel reliable and secure.
    5 Stars By Hulda from Curacao - 2015.11.04 10:32

    Send your message to us:

    INQUIRY NOW
    • * CAPTCHA: Please select the Heart

    Related Products

    INQUIRY NOW
    • * CAPTCHA: Please select the Plane

    WhatsApp Online Chat !
    function pcWhatsapp(){ document.getElementById("mo_whatsapp").setAttribute("class", "pc_whatsapp") } function moWhatsapp(){ document.getElementById("mo_whatsapp").setAttribute("class", "mo_whatsapp") } if( /Android|webOS|iPhone|iPad|iPod|BlackBerry|IEMobile|Opera Mini/i.test(navigator.userAgent) ) { moWhatsapp() }else{ pcWhatsapp() }