10 Years Manufacturer PTFE Gasket for Canberra Manufacturers
10 Years Manufacturer PTFE Gasket for Canberra Manufacturers Detail:
PTFE gasket is manufactured by molding method with PTFE granular resin. Compared with other plastic, PTFE has a superior properties against chemicals and temperature. Because of such excellent properties, PTFE gasket has a wide application as a sealing material.
Technical Data Sheet
Property | Unit | Result |
Density | g/cm3 | 2.18 |
Elongation at Break | % | 200~450 |
Tensile Strength | Mpa | 14~18 |
Bending Strength | Mpa | No Break |
Pressure Resistance | Mpa | 24 |
Tensile Modulus | Mpa | 393 |
Bending Modulus | Mpa | 490~586 |
Working Temperature
(20000 hr, highest) |
℃ |
260 |
Application Area
As a sealing material, PTFE gaskets can be used in flange joint of various equipments and pipes in chemical industry, food producing industry, medicine industry and so on. It can bear the most bitter chemical medium, and has good anti-creeping performance. The unloaded operating temperature range is -180~+260℃.
Product detail pictures:
Related Product Guide:
A Look at the Molded Gasket
Comparison of O-Ring Materials
10 Years Manufacturer PTFE Gasket for Canberra Manufacturers, The product will supply to all over the world, such as: , , ,
Toolfusion® 3 is a two part low viscosity epoxy infusion resin formulated to produce pre-preg quality, composite moulds. Toolfusion® 3 has a low initial cure temperature of 120ºF (49ºC) and can be post cured to achieve a high glass transition temperature of 425ºF (218ºC). Void contents of less than 1% are achievable. Toolfusion® 3 will work in various RTM and VARTM processes including single and double bag arrangements to produce autoclave quality laminates.
Benefits:
• Resin infusion process delivers very high quality laminates with low manufacturing costs, no refrigeration costs, no autoclave running costs.
• Low initial cure temperature for low thermal expansion effect during curing and ability to use low cost master model materials.
• Nano technology delivers outstanding toughness & high Tg. (218ºC) for long tool life and reduced life cycle cost.
• Low viscosity allows infusion of thicker and more complex laminates with fewer resin feed lines.
• In comparison to metallic tools, Toolfusion® 3 composite tools are lighter weight for easier manual handing.
• In comparison to metallic tooling, Toolfusion® 3 composite tools have faster heat up and cool down rates for reduced production costs.
• Toolfusion® 3 composite tooling laminates have vacuum integrity for vacuum bag processing of parts in oven and autoclave.
For more information, please visit: www.airtechonline.com
TERM Sealant Barrier – Termite barrier for plumbing penetrations
www.PolyguardBarriers.com
TERM Sealant Barrier is a sealant barrier, applied with a caulking gun or smoothing tool, and used for both waterproofing and insect
exclusion . TERM Sealant Barrier is a component of the non-structural TERM Barrier System which, when properly constructed as part of the building envelope, acts as a barrier to almost all pests. Because almost all pests are excluded for the life of the structure, the need for pesticide treatment should be permanently and drastically reduced.
Here are some of the places where it is used:
1. To seal slab penetrations above slab against termite entry
2. As a component of the TERM Full Bath Trap Barrier, to exclude
termites, fire ants, rodents, moles, etc. from entry underneath
bathtubs at ground level
3. To seal slab penetrations (prior to concrete pour) as a
component of the TERM Underslab Barrier
4. To detail small gaps found during construction in horizontal or
vertical portions of the TERM building envelope pest barrier.
Polyguard Products, Barrier Products Division
The Polyguard Particle Barrier is an insect exclusion product and is easy to install. Used around the perimeter of the building, it can significantly reduce the quantity of termiticides needed to protect the structure.
Polyguard has registered our barrier products with the EPA, who
along with state agencies regulates pesticides. However, Polyguard’s barriers are classified by the EPA as “devices”, since they contain no toxic components.
Termites trying to get into a structure are unable to penetrate the
Polyguard Particle Barrier. Also important, in the case of the
Reticuletermes flavipes species, is that the insects are unable to get out of a structure which they previously penetrated. In the majority of infested structures, there is not sufficient moisture in the building for Reticuletermes flavipes, so they have to come out to obtain moisture.
By from -
By from -